TIGm 1.1 - Submersible electric pump with single-phase grinder 1.5 HP
Flow rate up to 150 l/min (9 m³/h). Head up to 24 m. 1.1 Kw (1.5 HP) motor.
The Pedrollo TIGm 1.1 single-phase grinder pump is equipped with a high-resistance tempered stainless steel grinder.
The pump is equipped with a 10 meter cable, it can be immersed up to 5 meters underwater.
The TIGm 1.1 allows for the complete shredding of solid bodies and fibres contained in waste water and waste water in the domestic and civil sectors, for conveyance under pressure into the sewer system through small diameter pipes.
It has a flow rate that varies from 20 to 150 litres per minute with a head of 2 to 24 metres.
It must be powered by a single-phase voltage, has a horsepower of 1.5 HP and the temperature of the liquid to be pumped ranges from -15 degrees centigrade up to +40.
It has an IP68 certification which is safe from dust and water ingress.
The TIGm 1.1 is equipped with an external electrical panel for greater operational safety thanks to the special capacitor that significantly increases the torque. The panel includes a manually resettable motor protection switch.
The pump is made of materials such as cast iron and stainless steel which give the pump good resistance and allow it to last over time.
- Motor connection
- SINGLE-PHASE
- Power (Kw)
- 1.1
- Power (HP)
- 1.5
- Absorption at 230V (A)
- 6.7
- Delivery mouth
- 1" 1/2
- Pump body
- Cast iron
- Impeller
- Technopolymer
- Number of impellers
- 1
- Crankshaft
- AISI 431 stainless steel
- Check valve
- No
- Degree of protection
- IP 68
- Minimum flow rate (l./min.)
- 20
- Max. flow rate (l./min.)
- 150
- Min. head (m.)
- 2
- Max. head (m.)
- 24
- Cable length (m.)
- 10
- Jobs
- drainage
drying up
slightly dirty waters - Max. liquid temperature (°C)
- +40°C
- Height (cm)
- 43.2
- Width (cm)
- 19.5
- Depth (cm)
- 24.0
- Weight (Kg)
- 18.3
- Warranty (years)
- 2
TIGm models and performances
TIGm construction data
Construction

Bearings
| Pump side motor bearing | 6303 2RS-C3 |
| Opposite side engine bearing | 6203 ZZ-C3E |
Tree seal
| Type of seal | Double Mechanical Seal in oil chamber |
| LM diameter | 14 |
| LM fixed ring | Silicon Carbide |
| LM rotating ring | Graphite |
| LM Elastomer | NBR |
| Narrowing DN1=450 DN2=350 | MG1-14D SIC |
| LP diameter | 14 |
| LP fixed ring | Silicon Carbide |
| LP Rotating Ring | Silicon Carbide |
| LP Elastomer | NBR |
Materials
| 1.0 - Pump Body | Cast iron GJL 200 EN 1561 |
| 3.0 - Impeller | Technopolymer |
| 3.2 - Shredder | Stainless steel EN 1.4125 (AISI 440C) hardened |
| 4.0 - Pump Tree | Stainless steel EN 1.4057 (AISI 431) |
| 6.0 - Engine carrier | Stainless steel EN 1.4301 (AISI 304) |
| 7.0 - Lantern | Cast iron GJL 200 EN 1561 |



