6SR44/25 - PSR - 40 HP three-phase submersible electric pump
Flow rate up to 1000 l/min (60 m³/h). Head up to 310 m. 30 Kw (40 HP) motor.
The 6SR44/25 - PSR electric pump by Pedrollo is designed and built with the aim of providing good performance and at the same time a solid construction.
Equipped with impellers and diffusers made of special materials that can resist abrasion caused by sand. It supports pumping water for pumping with sand content not exceeding 100 grams per cubic meter.
The 6SR44/25 - PSR is recommended for use in the domestic, civil and agricultural sectors, in particular for the distribution of water in conjunction with pressure tanks, for irrigation, for pressure boosting and for fire-fighting systems.
The installation can be carried out up to 150 meters below the water level, thanks to the PSR engine and in wells with a diameter greater than 6 inches.
The flow rate varies from 200 to 1000 litres per minute with a head of 49 to 310 metres.
It must be powered by a three-phase voltage, has a horsepower of 40 HP and the temperature of the liquid to be pumped goes up to +35 degrees centigrade.
The 6SR44/25 - PSR is made of a mix of cast iron, AISI 304 stainless steel and noryl. Pedrollo has used this mix of materials to create a robust product that resists work and wear.
The 4-meter long power cable is supplied.
- Motor connection
- THREE-PHASE
- Power (Kw)
- 22
- Power (HP)
- 40
- Delivery mouth
- 3"
- Pump body
- Cast iron
- Impeller
- Noryl
- Number of impellers
- 25
- Crankshaft
- AISI 304 stainless steel
- Check valve
- No
- Degree of protection
- IP 68
- Minimum flow rate (l./min.)
- 200
- Max. flow rate (l./min.)
- 1000
- Min. head (m.)
- 49
- Max. head (m.)
- 310
- Cable length (m.)
- 4
- Jobs
- fire prevention systems
irrigation
pressurization systems
water supply - Max. liquid temperature (°C)
- +35°C
- Height (cm)
- 404.2
- External diameter (cm)
- 14.8
- Weight (Kg)
- 175.2
- Warranty (years)
- 2
Construction data of the 6SR36 series

Bearings
| Pump bearing - fixed part | Anti-friction polymer |
| Pump bearing - rotating part | Sintered AISI 316 steel with ceramic coating |
Tree holding
Materials
| 1.3 - Delivery body | Cast iron GJL 200 EN 1561 |
| 3.0 - Impeller | Reinforced technopolymer |
| 4.0 - Pump shaft | Stainless steel EN 1.4301 (AISI 304) |
| 4.2 - Towing joint | Stainless steel EN 1.4021 (AISI 420) |
| 5.0 - Stadium box | Stainless steel EN 1.4301 (AISI 304) |
| 5.1 - Diffuser | Reinforced technopolymer |
| 7.0 - Lantern | Cast iron GJL 200 EN 1561 |
| 7.1 - Check Valve | Stainless steel EN 1.4301 (AISI 304) |
| 7.2 - Pump shirt | Stainless steel EN 1.4301 (AISI 304) |
| 7.3 - Cable cover | Stainless steel EN 1.4301 (AISI 304) |
| 8.0 - Suction Grid/Filter | Stainless steel EN 1.4301 (AISI 304) |



