4BLOCKm 2/10 (20m) - 0.75 HP single-phase submersible electric pump
Flow rate up to 60 l/min (3.6 m³/h). Head up to 78 m. 0.55 kW (0.75 HP) motor. 20 m cable.
The 4-BLOCKm 2/10 submersible electric pump from Pedrollo 's 4-BLOCK series has independent floating impellers that make the presence of sand irrelevant.
It has a minimum efficiency index that far exceeds ErP requirements.
The 4-inch monoblock is top-of-the-line in terms of performance for its category.
The 4-BLOCKm 2/10 can be installed up to 100 metres below water level both horizontally and vertically.
Solid and robust thanks to Pedrollo 's use of AISI 304 and 431 stainless steel, technopolymer, brass and noryl.
- Motor connection
- SINGLE-PHASE
- Power (Kw)
- 0.55
- Power (HP)
- 0.75
- Absorption at 230V (A)
- 4
- Capacitor
- 20 µF 450 VL
- Delivery mouth
- 1" 1/4
- Pump body
- AISI 304 stainless steel
- Impeller
- Delrin
- Number of impellers
- 9
- Pump shaft
- AISI 304 stainless steel
- Check valve
- Yes
- Degree of protection
- IP 68
- Minimum flow rate (l./min.)
- 10
- Max. flow rate (l./min.)
- 60
- Min. head (m.)
- 29.5
- Max. head (m.)
- 78
- Cable length (m.)
- 20
- Jobs
- irrigation
pressurization systems
water supply - Max. liquid temperature (°C)
- +35°C
- Height (cm)
- 65.7
- External diameter (cm)
- 10
- Weight (Kg)
- 12.4
- Warranty (years)
- 2
4BLOCKm 2 models and performances
|
|
|
|
|
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Construction data of the 4BLOCK series

Bearings
| Pump side motor bearing | 6203 |
| Opposite side engine bearing | 6203 |
Tree holding
| Type of seal | Single Mechanical Seal in oil chamber |
| Engine side model | ST1-16 |
| LM diameter | 16 |
| LM fixed ring | Ceramic |
| LM rotating ring | Graphite |
| LM elastomer | NBR |
Materials
| 1.3 - Delivery body | Stainless steel EN 1.4301 (AISI 304) |
| 2.1 - Seal holder cover | Brass CW617N EN 12165 |
| 3.0 - Impeller | POM acetal resin |
| 4.0 - Pump shaft | Stainless steel EN 1.4301 (AISI 304) |
| 4.1 - Crankshaft | Stainless steel EN 1.4057 (AISI 431) |
| 5.0 - Stadium box | Stainless steel EN 1.4301 (AISI 304) |
| 5.1 - Diffuser | Reinforced technopolymer |
| 6.2 - Engine sleeve | Stainless steel EN 1.4301 (AISI 304) |
| 7.0 - Lantern | Reinforced technopolymer |
| 7.2 - Pump shirt | Stainless steel EN 1.4301 (AISI 304) |
| 7.3 - Cable cover | Stainless steel EN 1.4301 (AISI 304) |
| 8.0 - Suction Grid/Filter | Stainless steel EN 1.4301 (AISI 304) |



